A simple, cost-effective CanopyFlasher system. No Flarm interface. No Bluetooth.
One CanopyFlasher. One PowerBox.
Stand alone. Super simple. We call it LITE.
Stand-alone, canopy mounted forward-facing flasher
Six extremely bright red CREE™ LEDs built into an elegant, low profile Space Grey (Nextel like) enclosure, mounted in the front of the canopy. CanopyFlasher is made from a high strength, UV resistant ABS based polymer. Out of sight for you, but not for others:
The heart of the CanopyFlasher is the array of 6 extremely bright CREE LED’s emitting approximately 4000-4500 lumens, with powerful, oval lenses; two beams orientated vertically, and 4 beams orientated horizontally. This makes the Flasher well visible at distances of even up to 3500m, ±30 degrees above and below- and up to ±45 degrees left and right of the nose.
Safe to install
The CanopyFlasher system incorporated many safety features, like heat sinks, a temperature sensor to prevent overheat conditions and two status LED’s for indication of the operating mode and warnings.
CanopyFlasher is suitable for almost every glider, with canopies opening vertically and sideways.
PowerBox is fully stand-alone. It powers the CanopyFlasher LEDs and provides flashing sequencing logic (3 flashes per 1,5 second). This PowerBox is not connectable to Flarm, does not have Bluetooth features, and is not connectable to a FuselageFlasher. It’s the most simple, cost-effective solution for those who do not need all the “luxury” features.
PowerBox continuously monitors the temperature of the CanopyFlasher system. If an overheat situation is present, it automatically shuts down the system to prevent damage to the system and to your expensive canopy. After a short cooling the system will restart automatically if conditions permit. Don’t worry, the system generally doesn’t get very warm in flight, but in summer conditions on ground without air flow your glider is well protected.
A neat removable screw-terminal system allows a quick connection of the power wires, and easy removal when needed. No need for soldering; everything is plug-and-fly.
PowerBox is super compact and lightweight: it measures 50 x 63 x 31mm (including mounting flanges) and weighs only 100 grams.
Due to PowerBox’s smart technology, power consumption is very reasonable and should not be an obstacle to installing AeroFlash.
Red or white LEDs? Your choice…
Let’s explain the pros and cons:
+ Better visibility of a white glider against a grey/white background. This is the most dangerous situation. Red clearly stands out.
+ Red means danger.
– Slightly less brightness than white LEDs.
+ Slightly better brightness compared to red LEDs.
+ Better visibility against a brown/green background.
– Reduced visibility of a white glider against a grey/white background (in clouds, haziness, snowy terrain, etc).
We recommend RED. This gives the best result in the most dangerous situations, where it would be very difficult to be seen otherwise.
Scope of Delivery
1x PowerBox device.
1x CanopyFlasher with 3M double sided adhesive foam tape pre-applied and 60-100cm cable set.
1x 100cm DB9-DB9 extension cable.
1x PowerBox cable set with OFF/ON switch with marking/label.
1x 3M Dual Lock adhesive tape for mounting of PowerBox.
1x Vinyl template for aligning the CanopyFlasher during installation.[/vc_column_text]
Simply connect it to your power supply.
Canopy opening directions – different cable harnesses
Vertical opening – universal
Vertically opening canopies need an easy to attach, but most importantly, easy to DETACH connector. When jettisoning the canopy in case of an emergency, our connectors are designed to easily separate.
The AeroFLASH installation consists of commonly seen male and female DB9 (D SUB 9) type connectors for the data cables (status LEDs and temperature sensor), and for the power supply of the CanopyFlasher. It is sturdy, easy to attach, separate (locking screws removed), and highly suited for the currents.
The Flasher cable length is 100cm, suitable for every installation. Included as well is a 100cm extension cable.
Side opening – universal
Each glider type requires a specially designed connector solution. This is unique to every different glider type. A brief installation instruction manual together with installation example pictures will be delivered together with these orders.
On the side are a few examples suitable for Grob G102 Club/Standard Astir and G103 Twin Astir gliders.
If your glider is not yet supported, please contact us to develop a solution together.
Side opening – Schempp-Hirth type
For Schempp-Hirth panels we designed a special 7-pin spring loaded connector to be mounted on the glareshield/instrument panel cover and the canopy edge, which requires absolutely no force to separate. The connectors have two alignment pins, to avoid mis-alignments causing short circuits. There is no need to solder any wiring, however you will need to install the connector in a suitable location and drill some holes in the instrument panel cover. We include a mounting position and drilling template to make this a little easier. Also included are a few mounting support plates with various angles for optimal installation in your specific glider. Schempp-Hirth glider owners may also choose a panel mounted DB9 connector option if they have a lot of play in the instrument panel cover, as this should be fairly sturdy. Please refer to the installation manual for more details, or contact us.